View NCP707_7254197.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2013 april, 2013 ? rev. 1 1 publication order number: NCP707/d NCP707 200 ma, very-low quiescent current, i q 25 a, low noise, low dropout regulator the NCP707 is 200 ma ldo that provides the engineer with a very stable, accurate voltage with very low noise suitable for space constrained, noise sensitive app lications. in order to optimize performance for battery operated portable applications, the NCP707 employs the dynamic quiescent current adjustment for very low i q consumption at no ? load. features ? operating input voltage range: 1.9 v to 5.5 v ? available in fixed voltage options: 1.5 v to 3.3 v contact factory for other voltage options ? very low quiescent current of typ. 25 a ? very low noise: 22 v rms from 100 hz to 100 khz ? very low dropout: 120 mv typical at 200 ma ? 2% accuracy over load/line/temperature ? high power supply ripple rejection: 70 db at 1 khz ? thermal shutdown and current limit protections ? stable with a 1 f ceramic output capacitor ? available in xdfn 1.0 x 1.0 mm package ? these are pb ? free devices typical applicaitons ? pdas, mobile phones, gps, smartphones ? wireless handsets, wireless lan, bluetooth ? , zigbee ? ? portable medical equipment ? other battery powered applications figure 1. typical application schematic NCP707 in en out gnd off on v out c out 1 f ceramic c in v in xdfn4 mx suffix case 711aj marking diagram http://onsemi.com see detailed ordering and shipping information in the package dimensions section on page 18 of this data sheet. ordering information pin connection 1 x = specific device code m = date code x m 1 43 2 1 out gnd in en (top view) epad
NCP707 http://onsemi.com 2 in out voltage reference active discharge* mosfet driver with current limit thermal shutdown enable logic gnd auto low power mode en en figure 2. simplified schematic block diagram *active output discharge function is present only in NCP707amxyyytcg devices. yyy denotes the particular v out option. pin function description pin no. pin name description 1 out regulated output voltage pin. a small ceramic capacitor with minimum value of 1 f is needed from this pin to ground to assure stability. 2 gnd power supply ground. 3 en driving en over 0.9 v turns on the regulator. driving en below 0.4 v puts the regulator into shutdown mode. 4 in input pin. a small 1 f capacitor is needed from this pin to ground to assure stability. ? epad exposed pad should be connected directly to the gnd pin. soldered to a large ground copper plane allows for effective heat removal. absolute maximum ratings rating symbol value unit input voltage (note 1) v in ? 0.3 v to 6 v v output voltage v out ? 0.3 v to v in + 0.3 v v enable input v en ? 0.3 v to v in + 0.3 v v output short circuit duration t sc s maximum junction temperature t j(max) 150 c storage temperature t stg ? 55 to 150 c esd capability, human body model (note 2) esd hbm 2000 v esd capability, machine model (note 2) esd mm 200 v stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. refer to electrical characteristis and application information for safe operating area. 2. this device series incorporates esd protection and is tested by the following methods: esd human body model tested per eia/jesd22 ? a114 esd machine model tested per eia/jesd22 ? a115 latchup current rating tested per jedec standard: jesd78 thermal characteristics rating symbol value unit thermal characteristics, xdfn4 1x1 mm thermal resistance, junction ? to ? air r ja 250 c/w 3. single component mounted on 2 oz, fr4 pcb with 100 mm 2 cu area.
NCP707 http://onsemi.com 3 electrical characteristics ? 40 c t j 125 c; v in = v out(nom) + 0.5 v or 1.9 v, whichever is greater; i out = 10 ma, c in = c out = 1 f, unless otherwise noted. v en = 0.9 v. typical values are at t j = +25 c. min./max. are for t j = ? 40 c and t j = +125 c respectively (note 4). parameter test conditions symbol min typ max unit operating input voltage v in 1.9 5.5 v v out + 0.5 v v in 5.5 v, i out = 0 ? 200 ma v out ? 2 +2 % line regulation v out + 0.5 v v in 5.5 v, i out = 10 ma reg line 400 v/v load regulation i out = 0 ma to 200 ma reg load 10 v/ma load transient i out = 1 ma to 200 ma or 200 ma to 1 ma in 1 s, c out = 1 f tran load 75 mv dropout voltage (note 5) i out = 200 ma v out = 1.5 v v do 415 490 mv v out = 1.8 v 221 380 v out = 1.85 v 218 370 v out = 2.8 v 118 175 v out = 2.85 v 114 170 v out = 3.0 v 111 165 v out = 3.1 v 107 160 v out = 3.3 v 100 150 output current limit v out = 90% v out(nom) i cl 250 379 500 ma ground current i out = 0 ma i q 25 35 a i out = 2 ma i gnd 105 a i out = 200 ma i gnd 240 a shutdown current v en 0.4 v, v in = 5.5 v i dis 0.01 1 a en pin threshold voltage high threshold low threshold v en voltage increasing v en voltage decreasing v en_hi v en_lo 0.9 0.4 v en pin input current v en = 5.5 v i en 180 500 na turn ? on time c out = 1.0 f, from assertion of v en to 98% v out(nom) t on 200 s power supply rejection ratio v in = 3.6 v, v out = 3.1 v i out = 150 ma f = 100 hz f = 1 khz f = 10 khz psrr 58 70 55 db output noise voltage v out = 3.1 v, v in = 3.6 v, i out = 200 ma f = 100 hz to 100 khz v n 22 v rms thermal shutdown temperature temperature increasing from t j = +25 c t sd 160 c thermal shutdown hysteresis temperature falling from t sd t sdh 20 c active output discharge resist- ance v en < 0.4 v, version a only r dis 1.2 k 4. performance guaranteed over the indicated operating temperature range by design and/or characterization. production tested at t j = t a = 25 c. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible . 5. characterized when v out falls 100 mv below the regulated voltage at v in = v out(nom) + 0.5 v.
NCP707 http://onsemi.com 4 figure 3. output voltage vs. temperature v out = 1.5 v figure 4. output voltage vs. temperature v out = 1.85 v figure 5. output voltage vs. temperature v out = 2.85 v figure 6. output voltage vs. temperature v out = 3.0 v figure 7. output voltage vs. temperature v out = 3.1 v figure 8. output voltage vs. temperature v out = 3.3 v 1.510 1.505 1.500 1.495 1.490 1.485 1.480 ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) output voltage (v) i out = 10 ma i out c in = c out = 1 f v in = 2.0 v v out(nom) = 1.5 v junction temperature ( c) output voltage (v) 1.860 ? 40 ? 20 0 140 120 100 20 40 60 80 1.855 1.850 1.845 1.840 1.835 1.830 c in = c out = 1 f v in = 2.35 v v out(nom) = 1.85 v i out = 10 ma i out = 200 ma 2.870 ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) output voltage (v) 2.865 2.860 2.855 2.850 2.845 2.840 i out = 10 ma i out = 200 ma c in = c out = 1 f v in = 3.35 v v out(nom) = 2.85 v junction temperature ( c) output voltage (v) 3.000 ? 40 ? 20 0 140 120 100 20 40 60 80 2.995 2.990 2.985 2.980 2.975 2.970 i out = 10 ma i out = 200 ma c in = c out = 1 f v in = 3.5 v v out(nom) = 3.0 v 3.110 ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) output voltage (v) 3.105 3.100 3.095 3.090 3.085 3.080 c in = c out = 1 f v in = 3.6 v v out(nom) = 3.1 v i out = 10 ma i out = 200 ma junction temperature ( c) output voltage (v) 3.300 ? 40 ? 20 0 140 120 100 20 40 60 80 3.295 3.290 3.285 3.280 3.275 3.270 i out = 10 ma i out = 200 ma c in = c out = 1 f v in = 3.8 v v out(nom) = 3.3 v
NCP707 http://onsemi.com 5 figure 9. quiescent current vs. input voltage v out = 1.5 v figure 10. quiescent current vs. input voltage v out = 1.8 v figure 11. quiescent current vs. input voltage v out = 2.8 v figure 12. quiescent current vs. input voltage v out = 3.0 v figure 13. quiescent current vs. input voltage v out = 3.1 v figure 14. quiescent current vs. input voltage v out = 3.3 v 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 t a = 125 c c in = c out = 1 f i out = 0 ma v out(nom) = 1.5 v t a = 25 c t a = ? 40 c 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 c in = c out = 1 f i out = 0 ma v out(nom) = 1.8 v t a = 125 c t a = 25 c t a = ? 40 c 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 c in = c out = 1 f i out = 0 ma v out(nom) = 2.8 v t a = 125 c t a = 25 c t a = ? 40 c 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f i out = 0 ma v out(nom) = 3.0 v 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f i out = 0 ma v out(nom) = 3.1 v 35 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) quiescent current ( a) 30 25 20 15 10 5 0 3.5 3 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f i out = 0 ma v out(nom) = 3.3 v
NCP707 http://onsemi.com 6 figure 15. output voltage vs. input voltage v out = 1.5 v figure 16. output voltage vs. input voltage v out = 1.8 v figure 17. output voltage vs. input voltage v out = 2.8 v figure 18. output voltage vs. input voltage v out = 3.0 v figure 19. output voltage vs. input voltage v out = 3.1 v figure 20. output voltage vs. input voltage v out = 3.3 v 2.00 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) output voltage (v) 3.5 3 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0.00 c in = c out = 1 f i out = 0 ma v out(nom) = 1.5 v t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f i out = 0 ma v out(nom) = 1.8 v t a = 125 c t a = 25 c t a = ? 40 c 2.00 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) output voltage (v) 3.5 3 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0.00 c in = c out = 1 f i out = 0 ma v out(nom) = 2.8 v 3.50 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) output voltage (v) 3.5 3 t a = 125 c t a = 25 c t a = ? 40 c t a = 125 c t a = 25 c t a = ? 40 c 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 3.5 3 output voltage (v) 3.00 2.50 2.00 1.50 1.00 0.50 0.00 3.50 3.00 2.50 2.00 1.50 1.00 0.50 0.00 c in = c out = 1 f i out = 0 ma v out(nom) = 3.0 v input voltage (v) 3.50 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 input voltage (v) output voltage (v) 3.5 3 3.00 2.50 2.00 1.50 1.00 0.50 0.00 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f i out = 0 ma v out(nom) = 3.1 v 0 0.5 1 5.5 5 4.5 1.5 2 2.5 4 3.5 3 output voltage (v) 4.00 input voltage (v) 3.50 3.00 2.50 2.00 1.50 1.00 0.50 0.00 c in = c out = 1 f i out = 0 ma v out(nom) = 3.3 v t a = 125 c t a = 25 c t a = ? 40 c
NCP707 http://onsemi.com 7 figure 21. dropout voltage vs. output current v out = 1.5 v figure 22. dropout voltage vs. output current v out = 1.85 v figure 23. dropout voltage vs. output current v out = 2.8 v figure 24. dropout voltage vs. output current v out = 3.0 v figure 25. dropout voltage vs. output current v out = 3.1 v figure 26. dropout voltage vs. output current v out = 3.3 v 0 dropout voltage (v) 0.7 output current (a) 0.04 0.2 0.16 0.12 0.08 0.6 0.5 0.4 0.3 0.2 0.1 0 t a = 125 c c in = c out = 1 f v out(nom) = 1.5 v t a = 25 c t a = ? 40 c 0 dropout voltage (v) 0.45 output current (a) 0.04 0.2 0.16 0.12 0.08 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 0 dropout voltage (v) 0.200 output current (a) 0.04 0.2 0.16 0.12 0.08 0.175 0.150 0.125 0.100 0.075 0.050 0.025 0.000 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f v out(nom) = 1.85 v t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f v out(nom) = 2.8 v 0 output current (a) 0.04 0.2 0.16 0.12 0.08 0.200 0.175 0.150 0.125 0.100 0.075 0.050 0.025 0.000 dropout voltage (v) c in = c out = 1 f v out(nom) = 3.0 v t a = 125 c t a = 25 c t a = ? 40 c 0 dropout voltage (v) 0.200 output current (a) 0.04 0.2 0.16 0.12 0.08 0.175 0.150 0.125 0.100 0.075 0.050 0.025 0.000 0 output current (a) 0.04 0.2 0.16 0.12 0.08 0.200 0.175 0.150 0.125 0.100 0.075 0.050 0.025 0.000 dropout voltage (v) t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f v out(nom) = 3.1 v t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f v out(nom) = 3.3 v
NCP707 http://onsemi.com 8 figure 27. short ? circuit limit vs. temperature v out = 1.5 v figure 28. short ? circuit limit vs. temperature v out = 1.85 v figure 29. short ? circuit limit vs. temperature v out = 2.85 v figure 30. short ? circuit limit vs. temperature v out = 3.0 v figure 31. short ? circuit limit vs. temperature v out = 3.1 v figure 32. short ? circuit limit vs. temperature v out = 3.3 v junction temperature ( c) 440 output current (ma) ? 40 ? 20 0 140 120 100 20 40 60 80 420 400 380 360 340 320 300 short ? circuit current: i out for v out = 0 v c in = c out = 1 f v in = 2.0 v v out(nom) = 1.5 v current limit: i out for v out = v out(nom) ? 0.1 v junction temperature ( c) 440 output current (ma) ? 40 ? 20 0 140 120 100 20 40 60 80 420 400 380 360 340 320 300 short ? circuit current: i out for v out = 0 v current limit: i out for v out = v out(nom) ? 0.1 v c in = c out = 1 f v in = 2.35 v v out(nom) = 1.85 v junction temperature ( c) 440 output current (ma) ? 40 ? 20 0 140 120 100 20 40 60 80 420 400 380 360 340 320 300 short ? circuit current: i out for v out = 0 v c in = c out = 1 f v in = 3.35 v v out(nom) = 2.85 v current limit: i out for v out = v out(nom) ? 0.1 v junction temperature ( c) 440 output current (ma) ? 40 ? 20 0 140 120 100 20 40 60 80 420 400 380 360 340 320 300 short ? circuit current: i out for v out = 0 v current limit: i out for v out = v out(nom) ? 0.1 v c in = c out = 1 f v in = 3.5 v v out(nom) = 3.0 v junction temperature ( c) 440 output current (ma) ? 40 ? 20 0 140 120 100 20 40 60 80 420 400 380 360 340 320 460 short ? circuit current: i out for v out = 0 v c in = c out = 1 f v in = 3.6 v v out(nom) = 3.1 v current limit: i out for v out = v out(nom) ? 0.1 v junction temperature ( c) ? 40 ? 20 0 140 120 100 20 40 60 80 440 420 400 380 360 340 320 460 output current (ma) short ? circuit current: i out for v out = 0 v current limit: i out for v out = v out(nom) ? 0.1 v c in = c out = 1 f v in = 3.8 v v out(nom) = 3.3 v
NCP707 http://onsemi.com 9 figure 33. line regulation vs. temperature v out = 1.5 v figure 34. line regulation vs. temperature v out = 1.85 v figure 35. line regulation vs. temperature v out = 2.85 v figure 36. line regulation vs. temperature v out = 3.0 v figure 37. line regulation vs. temperature v out = 3.1 v figure 38. line regulation vs. temperature v out = 3.3 v junction temperature ( c) ? 40 ? 20 0 140 120 100 20 40 60 80 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 2 v to 5.5 v c in = c out = 1 f v in = 2.0 v to 5.5 v v out(nom) = 1.5 v i out = 10 ma ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 2.35 v to 5.5 v c in = c out = 1 f v in = 2.35 v to 5.5 v v out(nom) = 1.85 v i out = 10 ma junction temperature ( c) ? 40 ? 20 0 140 120 100 20 40 60 80 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 3.35 v to 5.5 v c in = c out = 1 f v in = 3.35 v to 5.5 v v out(nom) = 2.85 v i out = 10 ma ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 3.5 v to 5.5 v c in = c out = 1 f v in = 3.5 v to 5.5 v v out(nom) = 3.0 v i out = 10 ma junction temperature ( c) ? 40 ? 20 0 140 120 100 20 40 60 80 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 3.6 v to 5.5 v c in = c out = 1 f v in = 3.6 v to 5.5 v v out(nom) = 3.1 v i out = 10 ma ? 40 ? 20 0 140 120 100 20 40 60 80 junction temperature ( c) 5.0 line regulation (mv) 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 line regulation from v in = 3.8 v to 5.5 v c in = c out = 1 f v in = 3.8 v to 5.5 v v out(nom) = 3.3 v i out = 10 ma
NCP707 http://onsemi.com 10 figure 39. load regulation vs. temperature figure 40. ground current vs. output current figure 41. ground current vs. temperature figure 42. stability vs. output capacitor esr figure 43. psrr vs. frequency v out = 1.5 v figure 44. psrr vs. frequency v out = 1.85 v junction temperature ( c) 10 load regulation (mv) v out(nom) = 1.5 v c in = c out = 1 f v in = v out(nom) + 0.5 v i out = 0 ma to 200 ma 9 8 7 6 5 4 3 2 1 0 ? 40 ? 20 0 140 120 100 20 40 60 80 v out(nom) = 1.8 v v out(nom) = 3.3 v output current (ma) 200 ground current ( a) 012 10 9 8 3456 180 160 140 120 100 80 60 40 20 0 7 t a = 125 c c in = c out = 1 f v in = v out(nom) + 0.5 v t a = 25 c t a = ? 40 c junction temperature ( c) 300 ? 40 ? 20 0 140 120 100 20 40 60 80 ground current ( a) 280 260 240 220 200 c in = c out = 1 f v in = v out(nom) + 0.5 v i out = 200 ma v out(nom) = 1.5 v v out(nom) = 1.85 v v out(nom) = 3.3 v v out(nom) = 2.85 v output current (ma) 100 capacitor esr ( ) 0 10 1 0.1 0.01 100 200 300 unstable operation stable operation v out = 1.5 v v out = 3.3 v frequency (hz) 90 10 psrr (db) 80 70 60 50 40 30 20 10 0 100 1k 10k 100k 1m 10m c out = 1 f c in = none, v in = 2.0 v 50 mv ac v out(nom) = 1.5 v i out = 1 ma i out = 10 ma i out = 150 ma frequency (hz) 10 100 1k 10k 100k 1m 10m 90 psrr (db) 80 70 60 50 40 30 20 10 0 100 i out = 150 ma i out = 10 ma i out = 1 ma c out = 1 f c in = none, v in = 2.35 v 50 mv ac v out(nom) = 1.85 v
NCP707 http://onsemi.com 11 figure 45. psrr vs. frequency v out = 3.0 v figure 46. psrr vs. frequency v out = 3.1 v figure 47. output noise density vs. frequency v out = 1.5 v figure 48. output noise density vs. frequency v out = 3.1 v figure 49. enable input current vs. enable voltage figure 50. enable threshold voltage vs. temperature frequency (hz) 10 100 1k 10k 100k 1m 10m 90 psrr (db) 80 70 60 50 40 30 20 10 0 100 i out = 150 ma i out = 10 ma i out = 1 ma c out = 1 f c in = none, v in = 3.5 v 50 mv ac v out(nom) = 3.0 v frequency (hz) 10 100 1k 10k 100k 1m 10m 90 psrr (db) 80 70 60 50 40 30 20 10 0 i out = 150 ma i out = 1 ma i out = 10 ma c out = 1 f c in = none, v in = 3.6 v 50 mv ac v out(nom) = 3.1 v frequency (hz) 10 100 1k 10k 100k 1m output voltage noise ( v/rthz) 1.000 0.100 0.010 0.001 i out = 200 ma i out = 10 ma i out = 1 ma c in = c out = 1 f v in = 2.0 v v out = 1.5 v mlcc, x7r 1206 size frequency (hz) 10 100 1k 10k 100k 1m output voltage noise ( v/rthz) 1.000 0.100 0.010 0.001 c in = c out = 1 f v in = 3.6 v v out = 3.1 v mlcc, x7r 1206 size i out = 10 ma i out = 1 ma i out = 200 ma enable voltage (v) 0 0.5 1 3.5 4.5 5 5.5 enable current ( a) 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 4 3 1.5 2 2.5 t a = 125 c t a = 25 c t a = ? 40 c c in = c out = 1 f v in = 2 v v out(nom) = 1.5 v enable current ( a) junction temperature ( c) ? 40 ? 20 100 120 140 0.9 80 60 02040 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5 v in = 2 v c in = c out = 1 f v out(nom) = 1.5 v v en = low to high v en = high to low
NCP707 http://onsemi.com 12 figure 51. shutdown current vs. temperature figure 52. v out turn ? on time vs. temperature shutdown current ( a) junction temperature ( c) ? 40 ? 20 100 120 140 0.2 80 60 02040 0.16 0.12 0.08 0.04 0 c in = c out = 1 f v in = v out(nom) + 0.5 v v en = 0 v v out turn ? on time ( s) junction temperature ( c) ? 40 ? 20 100 120 140 300 80 60 02040 280 260 240 220 200 180 160 140 120 100 c in = c out = 1 f v in = v out(nom) + 0.5 v v en = step from 0 v to 1 v / 1 s v out = 3.3 v v out = 1.5 v
NCP707 http://onsemi.com 13 50 mv/div 100 ma / div 30 mv/div 100 ma / div 50 mv/div 100 ma / div 30 mv/div 100 ma / div 100 ma/div 1 v/div 1 v/div figure 53. load transient response i out = 1 ma to 200 ma, c out = 1 f 20 s / div v out i out v in = 3.6 v v out(nom) = 3.1 v c in = c out = 1 f 200 ma 1 ma figure 54. load transient response i out = 1 ma to 200 ma, c out = 4.7 f 20 s / div v in = 3.6 v v out(nom) = 3.1 v c in = c out = 4.7 f v out i out 200 ma 1 ma figure 55. load transient response i out = 10 ma to 200 ma, c out = 1 f 10 s / div figure 56. load transient response i out = 10 ma to 200 ma, c out = 4.7 f 20 s / div v in = 3.6 v v out(nom) = 3.1 v c in = c out = 1 f v in = 3.6 v v out(nom) = 3.1 v c in = c out = 4.7 f v out i out v out i out 200 ma 10 ma 200 ma 10 ma v out = 1.8 v v in = 2.3 v v out(nom) = 1.8 v c in = c out = 1 f i in = 1 ma v en = 1 v v out = 0 v v en = 0 v i in figure 57. enable turn ? on response v out = 1.8 v, c out = 1 f 500 s / div figure 58. enable turn ? off response v out = 1.8 v, c out = 1 f 500 s / div v out = 0 v v in = 2.3 v v out(nom) = 1.8 v c in = c out = 1 f v en = 0 v v en = 1 v v out = 1.8 v r l = 1.8 k r l = 180 k
NCP707 http://onsemi.com 14 100 ma/div 1 v/div v out = 1.8 v v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f i in = 1 ma v en = 1 v v en = 0 v i in figure 59. enable turn ? on response v out = 3.3 v, c out = 1 f 50 s / div v out = 0 v 1 v/div v out = 0 v v en = 0 v v en = 1 v v out = 1.8 v r l = 1.8 k r l = 180 k v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f figure 60. enable turn ? off response v out = 3.3 v, c out = 1 f 500 s / div 500 mv/div v out = 1.8 v v in = 2.3 v i in = 1 ma v out = 0 v v in = 0 v figure 61. enable turn ? on response v out = 1.8 v, c out = 1 f 500 s / div figure 62. enable turn ? off response v out = 1.8 v, c out = 1 f 2 ms / div 500 mv/div v out = 1.8 v v in = 2.3 v v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f v out = 0 v v in = 0 v 100 ma/div 1 v/div figure 63. enable turn ? on response v out = 3.3 v, c out = 1 f v out = 0 v v in = 0 v v out = 3.3 v v in = 3.8 v i in = 1 ma v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f v in = 3.8 v v out(nom) = 3.3 v c in = c out = 1 f 1 v/div v out = 3.3 v v in = 3.8 v v out = 0 v v in = 0 v figure 64. enable turn ? off response v out = 3.3 v, c out = 1 f
NCP707 http://onsemi.com 15 1 v/div i out = 1 ma v out = 1.5 v output short ? circuit figure 65. short ? circuit response v out = 1.5 v, c out = 1 f 200 s / div 200 ma/div v in = 5.5 v v out(nom) = 1.5 v c in = c out = 1 f i out = 402 ma v out = 0 v figure 66. short ? circuit response v out = 1.5 v, c out = 1 f 200 s / div v in = 5.5 v v out(nom) = 3.3 v c in = c out = 1 f i out = 398 ma output short ? circuit v out = 3.3 v v out = 0 v 1 v/div figure 67. short ? circuit response v out = 1.5 v, c out = 1 f 5 ms / div 200 ma/div 2 v/div 200 ma/div v in = 2.0 v v out(nom) = 1.5 v c in = c out = 1 f v out = 1.5 v i out = 1 ma thermal shutdown v out = 0 v i out = 398 ma
NCP707 http://onsemi.com 16 applications information the NCP707 is a high performance, small package size, 200 ma ldo voltage regulator. this device delivers very good noise and dynamic performance. thanks to its adaptive ground current feature the device consumes only 25 a of quiescent current at no ? load condition. the regulator features very*low noise of 22 vrms, psrr of typ. 70db at 1khz and very good load/line transient response. the device is an ideal choice for space constrained portable applications. a logic en input provides on/off control of the output voltage. when the en is low the device consumes as low as typ. 10 na from the in pin. the device is fully protected in case of output overload, output short circuit condition and overheating, assuring a very robust design. input capacitor selection (c in ) it is recommended to connect a minimum of 1 f ceramic x5r or x7r capacitor close to the in pin of the device. larger input capacitors may be necessary if fast and large load transients are encountered in the application. there is no requirement for the min./max. esr of the input capacitor but it is recommended to use ceramic capacitors for their low esr and esl. output capacitor selection (c out ) the NCP707 is designed to be stable with small 1.0 f and larger ceramic capacitors on the output. the minimum effective output capacitance for which the ldo remains stable is 100 nf. the safety margin is provided to account for capacitance variations due to dc bias voltage, temperature, initial tolerance. there is no requirement for the minimum value of equivalent series resistance (esr) for the c out but the maximum value of esr should be less than 700 m . larger output capacitors could be used to improve the load transient response or high frequency psrr characteristics. it is not recommended to use tantalum capacitors on the output due to their large esr. the equivalent series resistance of tantalum capacitors is also strongly dependent on the temperature, increasing at low temperature. the tantalum capacitors are generally more costly than ceramic capacitors. no ? load operation the regulator remains stable and regulates the output voltage properly within the 2% tolerance limits even with no external load applied to the output. enable operation the NCP707 uses the en pin to enable/disable its output and to control the active discharge function. if the en pin voltage is < 0.4 v the device is guaranteed to be disabled. the pass transistor is turned off so that there is virtually no current flow between the in and out. in case of the option equipped with active discharge ? the active discharge transistor is turned ? on and the output voltage v out is pulled to gnd through a 1.2 k resistor. in the disable state the device consumes as low as typ. 10 na from the v in . if the en pin voltage > 0.9 v the device is guaranteed to be enabled. the NCP707 regulates the output voltage and the active discharge transistor is turned off. the en pin has an internal pull ? down current source with typ. value of 180 na which assures that the device is turned ? off when the en pin is not connected. a build in 56 mv of hysteresis and deglitch time in the en block prevents from periodic on/off oscillations that can occur due to noise on en line. in the case that the en function isn?t required the en pin should be tied directly to in. reverse current the pmos pass transistor has an inherent body diode which will be forward biased in the case that v out > v in . due to this fact in cases where the extended reverse current condition is anticipated the device may require additional external protection. output current limit output current is internally limited within the ic to a typical 379 ma. the NCP707 will source this amount of current measured with the output voltage 100 mv lower than the nominal v out . if the output voltage is directly shorted to ground (v out = 0 v), the short circuit protection will limit the output current to 390 ma (typ). the current limit and short circuit protection will work properly up to v in =5.5 v at t a = 25 c. there is no limitation for the short circuit duration. thermal shutdown when the die temperature exceeds the thermal shutdown threshold (tsd 160 c typical), thermal sh utdown event is detected and the device is disabled. the ic will remain in this state until the die temperature decreases below the thermal shutdown reset threshold (tsdu ? 140 c typical). once the ic temperature falls below the 140 c the ldo is enabled again. the thermal shutdown feature provides protection from a catastrophic device failure due to accidental overheating. this protection is not intended to be used as a substitute for proper heat sinking. power dissipation as power dissipated in the NCP707 increases, it might become necessary to provide some thermal relief. the maximum power dissipation supported by the device is dependent upon board design and layout. mounting pad configuration on the pcb, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. the maximum power dissipation the NCP707 can handle is given by: p d(max) 125 t a ja (eq. 1)
NCP707 http://onsemi.com 17 for reliable operation junction temperature should be limited to +125 c. the power dissipated by the NCP707 for given application conditions can be calculated as follows: p d(max) v in i gnd i out v in v out (eq. 2) figure 68 shows the typical values of ja vs. heat spreading area. load regulation the NCP707 features very good load regulation of typical 2 mv in the 0 ma to 200 ma range. in order to achieve this very good load regulation a special attention to pcb design is necessary. the trace resistance from the out pin to the point of load can easily approach 100 m which will cause a 20 mv voltage drop at full load current, deteriorating the excellent load regulation. line regulation the ic features very good line regulation of 0.4 mv/v measured from v in = v out + 0.5 v to 5.5 v. power supply rejection ratio at low frequencies the psrr is mainly determined by the feedback open ? loop gain. at higher frequencies in the range 100 khz ? 10 mhz it can be tuned by the selection of c out capacitor and proper pcb layout. 0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 50 100 150 200 250 300 350 400 450 500 0 100 200 300 400 500 600 p d(max) (w) ja ( o c/w) copper area (mm 2 ) theta ja curve with pcb cu thk 1,0 oz theta ja curve with pcb cu thk 2,0 oz power curve with pcb cu thk 2,0 oz power curve with pcb cu thk 1,0 oz figure 68. thermal parameters vs. copper area output noise the ic is designed for very ? low output voltage noise. the typical noise performance of 22 v rms makes the device suitable for noise sensitive applications. internal soft start the internal soft start circuitry will limit the inrush current during the ldo turn ? on phase. please refer to typical characteristics section for typical inrush current values. the soft start function prevents from any output voltage overshoots and assures monotonic ramp ? up of the output voltage. pcb layout recommendations to obtain good transient performance and good regulation characteristics place c in and c out capacitors close to the device pins and make the pcb traces wide. in order to minimize the solution size use 0402 capacitors. larger copper area connected to the pins will also improve the device thermal resistance. the actual power dissipation can be calculated by the formula given in equation 2.
NCP707 http://onsemi.com 18 ordering information device voltage option marking marking rotation option package shipping ? NCP707amx150tcg 1.5 v a 0 with active output discharge function xdfn4 (pb-free) 3000 / tape & reel NCP707amx180tcg 1.8 v d 0 NCP707amx185tcg 1.85 v e 0 NCP707amx280tcg 2.8 v f 0 NCP707amx285tcg 2.85 v j 0 NCP707amx300tcg 3.0 v k 0 NCP707amx310tcg 3.1 v l 0 NCP707amx330tcg 3.3 v p 0 NCP707bmx150tcg 1.5 v a 90 without active output discharge function NCP707bmx180tcg 1.8 v d 90 NCP707bmx185tcg 1.85 v e 90 NCP707bmx280tcg 2.8 v f 90 NCP707bmx285tcg 2.85 v j 90 NCP707bmx300tcg 3.0 v k 90 NCP707bmx310tcg 3.1 v l 90 NCP707bmx330tcg 3.3 v p 90 ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
NCP707 http://onsemi.com 19 package dimensions xdfn4 1.0x1.0, 0.65p case 711aj issue o notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.20 mm from the terminal tips. 4. coplanarity applies to the exposed pad as well as the terminals. a b e d d2 bottom view b e 4x note 3 2x 0.05 c pin one reference top view 2x 0.05 c a a1 (a3) 0.05 c 0.05 c c seating plane side view l 4x 1 2 dim min max millimeters a 0.33 0.43 a1 0.00 0.05 a3 0.10 ref b 0.15 0.25 d 1.00 bsc d2 0.43 0.53 e 1.00 bsc e 0.65 bsc l 0.20 0.30 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. mounting footprint* 1.20 0.26 0.24 4x dimensions: millimeters 0.39 recommended package outline note 4 e/2 d2 45 a m 0.05 b c 4 3 0.65 pitch detail a 4x b2 0.02 0.12 l2 0.07 0.17 4x 0.52 2x 0.11 4x l2 4x detail a b2 4x on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other intellectual property. a list ing of scillc?s product/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parame ters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 NCP707/d bluetooth is a registered trademark of bluetooth sig. zigbee is a registered trademark of zigbee alliance. literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of NCP707

	To Download NCP707 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .